Projects

CITY TO SEA WEST PATHWAY

LIGHT THAT FOLLOWS YOU HOME.

A shared pathway that needs to be safe after dark. A regenerating river corridor where protecting the night environment matters. And three kilometres of mature, protected trees that make conventional streetlighting design anything but straightforward.

Designed for Christchurch City Council, the first stage of the City to Sea West Pathway runs through the Residential Red Zone along the Ōtākaro Avon River. The design uses warm-coloured LED lighting, carefully controlled optics and motion sensors to provide appropriate light when people need it while maintaining lower lighting levels when the pathway is unoccupied.

Site briefing 

  • Client: Christchurch City Council – Residential Red Zone Parks Unit
  • Location: Ōtākaro Avon River Corridor, Richmond and Burwood, Ōtautahi / Christchurch
  • Scope: Lighting design for the first 3 km stage of a shared walking and cycling pathway
  • Lighting: AEC I-Tron Zero, 2200K, installed on 6 m poles with zero upward light output at 0° tilt
  • Controls: Motion-activated lighting, increasing from PP3 to PP2 as pathway users approach (AS/NZS 1158)
  • Partners: Techlight NZ, CORDE, Boffa Miskell, Isthmus
  • Recognition: IES ANZ NZ Chapter Award of Commendation; RASNZ Dark Sky Lighting Design – Highly Commended (2026)

The challenge

The Residential Red Zone matters to the people who live around it. Land that was once suburban streets is now a regenerating river corridor, and the community has been clear that it should stay a predominantly dark place at night.

A four-year NIWA study of Christchurch’s own streetlights found insects are more strongly drawn to light as it gets brighter and bluer, with caddisflies among those most affected.¹ They’re food for the river’s fish and birds, so what draws them off the water matters well beyond the bugs.

But this isn’t a nature trail in the typical sense. The pathway is a commuter route, used by people walking and cycling to and from work, with few houses overlooking it. Light it too dimly and people stop feeling safe using it after dark, which defeats the point of building it.

Christchurch City Council’s brief put numbers on that balance. Light at 2200K or warmer. No upward light output at the specified 0° installation tilt. Less than 10 lux at ground level. Enough light to meet PP2, the brighter of the two pathway levels in AS/NZS 1158, when someone’s on the path, while running at the dimmer PP3 level the rest of the time. Motion sensors provide that change, with controllers designed for future integration with the council’s central streetlight management system. And every part of the installation had to stack up on sustainability too, from the lights to the poles and controls.

Then there were the trees. Mature, protected trees line much of the corridor, and their roots and canopy drip lines ruled out conventional pole placement along long stretches of the route. Every pole needed a spot that kept the trees healthy and the path compliant.

Our approach

The brief ruled out most of the market before the design started. Our lighting design team assessed five luminaires against the council’s eight weighted criteria, covering light performance, environmental impact, compatibility with adaptive controls, and whole-of-life sustainability. Anything that couldn’t meet the dark sky requirements didn’t make the final round.

The AEC I-Tron Zero, supplied by Techlight NZ, came out on top. It pairs a warm 2200K light source with precise optics that put light on the path and provide zero upward light output at 0° tilt. Modelling at a 6 m mounting height showed it met PP3 for both horizontal and vertical light, while keeping ground-level light under 10 lux. Vertical light is what lets you see the face of someone coming towards you. And the same fittings have the headroom to step up to PP2.

The controls are what make the path feel different to use. Each light carries its own motion sensor, linked to a controller designed for future integration with the council’s streetlight management system. As someone walks or rides along the path, the lights progressively lift to PP2, then ease back down after a set delay once they’ve passed. The effect is a wave of light that moves with each person, on a path that sits dimmed the rest of the time. Seasonal programming can reduce operating hours further in summer, when long evenings make lighting unnecessary.

The lighting design was coordinated with the landscape planting, so plants help screen light from the river. It’s an approach NIWA’s research recommends for reducing insect attraction near waterways.¹

The poles got the same scrutiny as the lights. Aluminium poles were selected with consideration for recyclability and durability in the riverside environment. The luminaire selection also considered available lifecycle environmental product documentation, alongside lighting performance and control requirements.

“This project was about more than meeting lighting standards. It required balancing pathway safety with the surrounding environment and the challenges of working around established trees. The result is a practical lighting solution that provides light where it’s needed while respecting the environment.”

Brendan Hayman MIES

Lighting Design Lead & Principal Design Engineer

Making it happen

On most pathway jobs, pole positions come from spacing and light calculations. On this one, the trees had a say too.

Our design team worked closely with the project arborist to find pole positions clear of sensitive root zones and canopy drip lines, then checked that each one still delivered the light levels the standard requires.

A plan only goes so far in a corridor of mature trees. So our people were on site during construction, adjusting pole positions in real time as the installation went in. Every adjustment had two jobs to do. Move a pole to protect a root and the spread of light along the path changes with it, so each change was weighed against both the tree’s health and AS/NZS 1158 before the pole went in.

Construction was delivered by Connetics alongside CORDE, with the lighting design team staying involved from the first pole to the last.

The controls went in at the same time. Every light’s motion sensor and controller has been installed and commissioned, so the wave of light already follows people along the path. Full connection to the council’s central street light management system will follow as CCC extends that network into this part of the corridor, and the hardware is already in place for it.

The result

The completed installation demonstrates how thoughtful design and adaptive technology can balance pathway safety, environmental sensitivity and infrastructure performance. It also shows the value of close collaboration between designers, clients, landscape specialists and construction teams in a sensitive river corridor.

Lighting a path for people while keeping a river corridor dark takes more than one team. Our thanks go to Christchurch City Council, whose brief put the river’s wildlife on the same footing as the people using the path, and who trusted us to find the balance.

We’re equally grateful to our delivery partners. CORDE built the pathway with our crews alongside, adjusting pole positions on the go. Boffa Miskell’s ecologist held the design to what the river corridor needed, then confirmed the finished installation met it. Isthmus shaped the planting that now screens light from the water. The project arborist helped us find room for poles between protected roots. And Techlight NZ supplied the luminaires and backed the night photography that shows the result.

Got a project taking shape?

Whether you’re still working out what’s needed or you’re ready to get started – get in touch and we’ll make sure it gets to the right person.

Contact us